ABB Feather Duster Product Manual Download Page 99

Page: 99 / 150

2573

2518

(1x) 3HAW050024261_Exhaust Flange

(2x) 3HAW050024239_Clamp

(1x) 3HAW050027151_SPACER

(4x) Screw, M6x20, DIN912, 8.8

(4x) Nut, M6, DIN934

(4x) Washer, M6, DIN9250

(1x) 3HAW050024379_Exhaust pipe support

(4x) Screw, M6x25, DIN912, 8.8

(4x) Nut, M6, DIN934

(4x) Washer, M6, DIN9250

(1x) 3HAW050024379_Exhaust pipe support

(4x) Screw, M6x25, DIN912, 8.8

(4x) Nut, M6, DIN934

(4x) Washer, M6, DIN9250

(1x) 3HAW050024379_Exhaust pipe support

(4x) Screw, M6x20, DIN912, 8.8

(4x) Washer, M6, DIN9250

(1x) 3HAW050024379_Exhaust pipe support

(4x) Screw, M6x20, DIN912, 8.8

(4x) Washer, M6, DIN9250

(1x) 3HAW050024235_Pipe frame_2ND axi

(2x) Screw, M12x20, DIN912, 8.8

(2x) Washer, M12, DIN934

(1x) 3HAWL001003_Exhaust hose

(1x) 3HAW050024366_Fixing plate1

(4x) Screw, M6x16, DIN912, 8.8

(4x) Washer, M6, DIN934

(1x) 3HAWL001001_Tubing Cable Protection

(1x) 3HAW050024272_Tubing

(1x) 3HAW050024374_Protection Shell

(1x) 3HAW050024375_90 Degree Joint

(2x) 3HAW050024247_Cable Ball joint clamp 36mm

(2x) 3HAW050024276_Standard Protector 36mm

(2x) 3HAW050024277_Gripping Clamp Hose 52mm

(4x) Screw, M8x12, DIN912, 8.8

(4x) Washer, M8, DIN9250

(2x) 3HAW050024239_Clamp

(1x) 3HAW050027152_Robot Cover plate

(1x) 3HAW050024379_Exhaust pipe support

(4x) Screw, M6x20, DIN912, 8.8

(4x) Washer, M6, DIN9250

1264

(1x) 3HAW050024237_Support Frame Axis 1

(4x) Screw, M20x35, DIN912, 8.8

(4x) Washer, M20, DIN9250

(1x) 3HAW050024368_Fixing plate 3

(4x) Screw, M6x16, DIN912, 8.8

(4x) Nut, M6, DIN934

(4x) Washer, M6, DIN9250

(1x) 3HAW050046163_Bracket Support_IRB6700

(2x) Screw, M8x25, DIN912, 8.8

(2x) Washer, M8, DIN9250

(1x) 3HAW050024370_Axis 3 Support

(4x) Screw, M8x20, DIN912, 8.8

(4x) Washer, M8, DIN934

(1x) 3HAW050024371_Extend support plate

(4x) Screw, M6x20, DIN912, 8.8

(4x) Washer, M6, DIN934

(1x) 3HAW050024369_Axis 3Fixing Plate

(2x) Screw, M12x20, DIN912, 8.8

(2x) Washer, M12, DIN9250

DETAIL A

SCALE 1 : 5

(1x) 3HAW050046161_Adapter Flange_6TH axi_IRB6700

(1x) 3HAW050046159_Joint Plate_IRB6700-200/260

"Casting Pre-2016" option

DETAIL B

SCALE 1 : 2

(1x) 3HAW050046186_Adapter Flange

(1x) 3HAW050046301_Seal

(11x) Screw M12x35, 12.9, DIN912

(11x) Washer M12, DIN9250

(1x) Pin 12x28, DIN7979D

"Casting Post-2016" option

(4x) 3HAW050046073_Convert Adapter_IRB6700_LL

(8x) Screw M6x40, 12.9, DIN912

(4x) Screw M8x20, 12.9, DIN912

(4x) Washer M8, DIN9250

OPTION 1

: robot wrist "Casting Pre-2016" vs "Casting Post-2016"

Date

Name

Modifications/ Revisions

Repere

Item NO.

Indice

Update

04-01-2016

King Jin

Option added for different casting wrist; Sub-part 3HAW050024369 revised.

01-12-2016

King Jin

Sub-part 3HAW050046159 (Joint Plate_IRB6700-200/260) revised.

11-17-2015

King Jin

Sub-assembly 3HAW050024379 (Exhaust pipe support) revised.

DRESSPACK OPTIONS

Item

Dresspack BoM

Options Group 1(Casting type)

Options Group 2(Arm length)

Note

3HAW050024378B

"New casting" (Axis 5 post-2016)

Compatible with calibration pin

3HAW050024378C

"Old casting" (Axis 5 pre-2016)

Feather Duster Dresspack_IRB6700_LL Wrist

FEATHER DUSTER

F LEGELEUX

1 cm

1:10

Scale:

Designation: Part, sub-assembly or Assembly

Brut:

Threatment:

Material:

VISA:

Dpt: R & D

Plant: CNAUS

Par:

Date: 4/5/2016

fax: +86 2161056905

tel: +86 2161298980

Shanghai, PRC

201319 Nanhui District

No5, Lane 369



Engineering Ltd



Ce document est la propriété de ABB Body In White SA et ne peut être

reproduit ou communiqué à des tiers sans autorisation écrite préalable

Engineering by:

1/1

Sheet:

Vehicle:

3HAW050024378

Drawing

Classement

Summary of Contents for Feather Duster













































































































































Search results

Summary of Contents for Feather Duster

Reviews:

Brands by name

Popular brands

ABB Feather Duster, Product Manual

Search results

Summary of Contents for Feather Duster

Reviews:

Brands by name

Popular brands