ABB Feather Duster Product Manual Download Page 26

Page: 26 / 150

1 Safety

1.4.6. Safe use of the Teach Pendant Unit

3HAW050027150 Revision: C

rig

t 201

101

6 ABB. All righ

ts reser

ed.

1.4.6. Safe use of the Teach Pendant Unit

NOTE!

The enabling device is a push button located on the side of the Teach Pendant Unit (TPU)

which, when pressed halfway in, takes the system to MOTORS ON. When the enabling

device is released or pushed all the way in, the robot is taken to the MOTORS OFF state. To

ensure safe use of the Teach Pendant Unit, the following must be implemented:

•

The enabling device must never be rendered inoperative in any way.

•

During programming and testing, the enabling device must be released as soon as

there is no need for the robot to move.

•

The programmer must always bring the Teach Pendant Unit with him/her, when

entering the robot's working space. This is to prevent anyone else taking control of the

robot without the programmer knowing.

Summary of Contents for Feather Duster













































































































































Search results

Summary of Contents for Feather Duster

Reviews:

Brands by name

Popular brands

ABB Feather Duster, Product Manual

Search results

Summary of Contents for Feather Duster

Reviews:

Brands by name

Popular brands