ABB Feather Duster Product Manual Download Page 23

Page: 23 / 150

1 Safety

1.4.3. Emergency release of the robots/manipulators axes

3HAW050027150 Revision: C

rig

t 201

101

6 ABB. All righ

ts reser

ed.

1.4.3. Emergency release of the robots/manipulators axes

Description

In an emergency situation, any of the robot's/manipulators axes may be released manually by

pushing the brake release buttons on the robot.

How to release the brakes is detailed in the robot product manual.

•

The robot arm may be moved manually on smaller robot models, but larger models

may require using an overhead crane or similar.

Increased injury

Before releasing the brakes, make sure that the weight of the arms does not increase the

pressure on the trapped person, further increasing any injury!

Summary of Contents for Feather Duster













































































































































Search results

Summary of Contents for Feather Duster

Reviews:

Brands by name

Popular brands

ABB Feather Duster, Product Manual

Search results

Summary of Contents for Feather Duster

Reviews:

Brands by name

Popular brands