ABB Feather Duster Product Manual Download Page 14

Page: 14 / 150

1 Safety

1.2.1. Safety in the robot system

3HAW050027150 Revision: C

rig

t 201

101

6 ABB. All righ

ts reser

ed.

1.2 General safety information

1.2.1. Safety in the robot system

Validity and responsibility

The information does not cover how to design, install and operate a complete system, nor

does it cover all peripheral equipment, which can influence the safety of the total system. To

protect personnel, the complete system must be designed and installed in accordance with the

safety requirements set forth in the standards and regulations of the country where the robot

is installed.

The users of ABB industrial robots are responsible for ensuring that the applicable safety laws

and regulations in the country concerned are observed and that the safety devices necessary

to protect people working with the robot system are designed and installed correctly.

Personnel working with robots must be familiar with the operation and handling of the

industrial robot, described in the applicable documents, e.g. User's Guide and Product

Manual.

Connection of external safety devices

Apart from the built-in safety functions, the robot is also supplied with an interface for the

connection of external safety devices. Via this interface, an external safety function can

interact with other machines and peripheral equipment. This means that control signals can

act on safety signals received from the peripheral equipment as well as from the robot.

Limitation of liability

Any information given in this manual regarding safety, must not be construed as a warranty

by ABB that the industrial robot will not cause injury or damage even if all safety instructions

are complied with.

Related information

Type of information

Detailed in document

Section

Installation of safety devices

Product manual for the robot

Installation and
commissioning

Changing robot modes

Operators manual
(RobotWare 5.0)

Operating modes

Restricting the working space Product manual for the robot

Installation and
commissioning

Summary of Contents for Feather Duster













































































































































Search results

Summary of Contents for Feather Duster

Reviews:

Brands by name

Popular brands

ABB Feather Duster, Product Manual

Search results

Summary of Contents for Feather Duster

Reviews:

Brands by name

Popular brands