ABB Feather Duster Product Manual Download Page 21

Page: 21 / 150

1 Safety

1.4.1. Safety fence dimensions

3HAW050027150 Revision: C

rig

t 201

101

6 ABB. All righ

ts reser

ed.

1.4 Safety actions related to the robot

1.4.1. Safety fence dimensions

General

Install a safety cell around the robot to ensure safe robot installation and operation.

Dimensioning

Dimension the fence or enclosure to enable it to withstand the force created if the load being

handled by the robot is dropped or released at maximum speed. Determine the maximum

speed from the maximum velocities of the robot axes and from the position at which the robot

is working in the work cell (see

Product Specification - Description, Robot Motion

Also consider the maximum possible impact caused by a breaking or malfunctioning rotating

tool or other device fitted to the manipulator.

Summary of Contents for Feather Duster













































































































































Search results

Summary of Contents for Feather Duster

Reviews:

Brands by name

Popular brands

ABB Feather Duster, Product Manual

Search results

Summary of Contents for Feather Duster

Reviews:

Brands by name

Popular brands