ABB DPA UPScale ST40 User Manual Download Page 9

Page: 9 / 129

Modifications reserved

Page 9/79

The DPA UPScale

will provide your critical equipment with a steady and reliable power supply for

many years.

The unique and modular UPS DPA UPScale belongs to the newest generation of midrange three-

phase UPS systems. High reliability, low operating costs and excellent electrical performance are only

some of the highlights of this innovative UPS solution.

The criteria and methods implemented at ABB for the design and manufacture correspond to the

most stringent quality standards.

The manufacturer is certified successfully in every area required by the international standard ISO
9001/EN 29001. The UPS is certified according to the norm IEC 62 040-3 and VDE 0558 Part 530 is

also accomplished.

The UPS has the Classification Code VFI-SS-111.

2.2

Nameplate and identification

The technical specifications of the equipment are provided on the nameplate, which is situated at the

front of the UPS. Check if it corresponds to the purchased material mentioned in the delivery note.

Fig 2.2-1: Nameplate

TYPE

PRODUCT DESCRIPTION

DIMENSIONS

S2UPxxx

DPA UPScale ST 40

Cabinet (550x1135x770mm)

S3UPxxx

DPA UPScale ST 60

Cabinet (550x1975x770mm)

S4UPxxx

DPA UPScale ST 80

Cabinet (550x1135x770mm)

S6UPxxx

DPA UPScale ST 120

Cabinet (550x1975x770mm)

S0UPxxx

DPA UPScale ST 200

Cabinet (550x1975x770mm)

Summary of Contents for DPA UPScale ST40




























































































































Search results

Summary of Contents for DPA UPScale ST40

Reviews:

Brands by name

Popular brands

ABB DPA UPScale ST40, User Manual

Search results

Summary of Contents for DPA UPScale ST40

Reviews:

Brands by name

Popular brands