ABB DPA UPScale ST40 User Manual Download Page 64

Page: 64 / 129

Modifications reserved

Page 64/79

Close internal and/or external battery fuses/breaker of the new module

Press both “ON/OFF” buttons simultaneously to start up UPS module.

All modules shall show to be in

LED Indicator

Color

LINE 1

Green

LINE 2

Green

BYPASS

Green

INVERTER

OFF

BATTERY

Green

Open Maintenance Bypass (IA1) by turning it to position “OFF”. The load is now supplied by

the static bypass of all three modules. Check the LED indicators on control panels.

Transfer load to inverter mode by means of COMMAND “LOAD TO INVERTER” on any one of
control panels. On LCD: “LOAD PROTECTED” will appear and the LED indicator will indicate

as shown below:

LED Indicator

Color

LINE 1

Green

LINE 2

Green

BYPASS

OFF

INVERTER

Green

BATTERY

Green

THE LOAD IS NOW PROTECTED BY THE DPA UPScale

Summary of Contents for DPA UPScale ST40




























































































































Search results

Summary of Contents for DPA UPScale ST40

Reviews:

Brands by name

Popular brands

ABB DPA UPScale ST40, User Manual

Search results

Summary of Contents for DPA UPScale ST40

Reviews:

Brands by name

Popular brands