ABB DPA UPScale ST40 User Manual Download

Page: 67 / 129

Modifications reserved

Page 67/79

Options

8.1

System

8.1.1

Backfeed protection

The UPS backfeed protection prevents any hazardous voltage or energy from being present on the
UPS input AC terminals after interruption of the input AC power.

The backfeed protection is implemented in the DPA UPScale ST by internal backfeed protection

contactors (K1 and K2) as shown in the wiring diagram below.

Fig 8.1.1-1: Backfeed protection

Mains backfeed contactor
(option)

In the event of an AC failure, prevents the occurrence of any

hazardous voltage at the rectifier mains terminal due to
backfeed from the power modules sourced by the battery

Bypass backfeed contactor
(option)

In the event of an AC failure, prevents the occurrence of any

hazard voltage at the bypass input terminal due to backfeed
from the power modules sourced by the battery

Order Number

04-0727

Backfeed protection ST40

04-0728

Backfeed protection ST60

04-0729

Backfeed protection ST80

04-0730

Backfeed protection ST120

04-3229

Backfeed protection ST200

Summary of Contents for DPA UPScale ST40




























































































































Search results

Summary of Contents for DPA UPScale ST40

Reviews:

Related manuals for DPA UPScale ST40

Brands by name

Popular brands

ABB DPA UPScale ST40, User Manual

Search results

Summary of Contents for DPA UPScale ST40

Reviews:

Related manuals for DPA UPScale ST40

Brands by name

Popular brands