ABB ACS 600 MultiDrive, Hardware Manual

Page: 54 / 94

Appendix A – ACS/ACC/ACP 604/607 Technical Data
A-10 ACS/ACC/ACP 604/607 Frequency Converters
NIOC Board
External control connections of NIOC board for ACS 600 with Standard
Application Software (Factory Macro) are below. External control
connections are different with other application macros and programs
(see
Firmware Manual).
A
C
S
6
01/604
/607
NIO
C
Bo
a
rd
(A
2
)
Programmable I/O
Factory Settings
X21
1 VREF Reference voltage
10 V d.c.
1 k
Ω
<
R
L
< 10 k
Ω
2 GND
3 AI1+ Speed reference
0(2) ... 10 V
R
in
> 200 k
Ω
4 AI1-
5 AI2+ By default, not in use.
0(4) ... 20 mA , R
in
= 100
Ω
6 AI2-
7 AI3+ By default, not in use.
0(4) ... 20 mA , R
in
= 100
Ω
8 AI3-
9 AO1+ Motor speed 0(4)...20 mA
0...motor nom. speed, R
L
< 700
Ω
10 AO1-
11 AO2+ Output current
0(4)...20 mA
0...motor nom. current, R
L
< 700
Ω
12 AO2-
X22
1 DI1 Stop/Start
2 DI2 Forward/Reverse
1)
3 DI3 Not used
4 DI4 ACCEL/DECEL 1/2
5 DI5 Constant speed select
2)
6 - Constant speed select
2)
7 +24V +24 V d.c. max. 100 mA
8 +24V
9 DGND Digital Ground
X23
1 +24 V Auxiliary voltage output, non-isolated,
24 V d.c. 250 mA
2 GND
X25
1 RO11 Relay output 1
Ready
2 RO12
3 RO13
X26
1 RO21
Relay output 2
Running
2 RO22
3 RO23
X27
1 - Relay output 3
Fault (-1)
2 -
3 -
=
=
2)
Operation: 0 = Open, 1 = Closed
DI 5 DI 6 Output
0
1
0
1
0
0
1
1
Set speed through AI1
Constant Speed 1
Constant Speed 2
Constant Speed 3
1
2
3
5
6
TRANS
B-
A+
GND
+24 V
Connector X29 for RS 485 connection
4
FAULT
1
2
3
4
5
6
TRANS
GND
B-
A+
GND
+24 V
Connector X28 for RS 485 connection
Panel Link Connections with NAMC-3. Not
in use with NAMC-11.
Terminal Block Size
X21, X22, X23, X25, X26, X27: cables 0.5 to 1.5 mm
2
Control Cable Lead-through Size:
Ø: 2 x 3x2...11 mm
Factory settings of application software
selection B (type code):
DI1: Start, DI2: Stop, DI3: Reverse, DI4:
Acc/Dec 2, DI5,6: Constant speed 1 to 3 select.
Fault
A
rpm
Power to Remote Panel with NAMC-3. Not
in use with NAMC-11.
Panel Link Connections with NAMC-3. Not
in use with NAMC-11.
Power to Remote Panel with NAMC-3. Not
in use with NAMC-11.