•
STO fault indication (parameter
31.22
) delay: < 500 ms
•
STO warning indication (parameter
31.22
) delay: < 1000 ms
■
Abbreviations
Description
Reference
Abbr.
Classification of the safety-related parts of a control system
in respect of their resistance to faults and their subsequent
behavior in the fault condition, and which is achieved by the
structural arrangement of the parts, fault detection and/or by
their reliability. The categories are: B, 1, 2, 3 and 4.
EN ISO 13849-1
Cat.
Common cause failure (%)
EN ISO 13849-1
CCF
Diagnostic coverage
EN ISO 13849-1
DC
Hardware fault tolerance
IEC 61508
HFT
Mean time to dangerous failure: (Total number of life units)
/ (Number of dangerous, undetected failures) during a partic-
ular measurement interval under stated conditions
EN ISO 13849-1
MTTFD
Average probability of dangerous failure on demand, that is,
mean unavailability of a safety-related system to perform the
specified safety function when a demand occurs
IEC 61508
PFDavg
Average frequency of dangerous failures per hour, that is,
average frequency of a dangerous failure of a safety related
system to perform the specified safety function over a given
period of time
IEC 61508
PFH
Performance level. Levels a…e correspond to SIL
EN ISO 13849-1
PL
Systematic capability
IEC 61508
SC
Safe failure fraction (%)
IEC 61508
SFF
Safety integrity level (1…3)
IEC 61508
SIL
Maximum SIL (level 1…3) that can be claimed for a safety
function or subsystem
IEC/EN 62061
SILCL
Safe torque off
IEC/EN 61800-5-2
STO
Proof test interval. T1 is a parameter used to define the
probabilistic failure rate (PFH or PFD) for the safety function
or subsystem. Performing a proof test at a maximum interval
of T1 is required to keep the SIL capability valid. The same
interval must be followed to keep the PL capability (EN ISO
13849) valid.
IEC 61508-6
T1
See also section Maintenance.
The Safe torque off function 289
Summary of Contents for ACQ580-07
