■
Connection examples of two-wire and three-wire sensors to analog
input (AI2)
Note:
The maximum capability of the auxiliary voltage output (24 V DC [250 mA]) must
not be exceeded.
An example of a two-wire sensor/transmitter supplied by the drive auxiliary voltage
output is shown below. Set the input signal to 4…20 mA, not 0…20 mA.
4…20 mA
+
-
P
I
...
AI2
AGND
+24V
DGND
An example of a three-wire sensor/transmitter supplied by the drive auxiliary voltage
output is shown below.The sensor is supplied through its current output and the drive
feeds the supply voltage (+24 V DC). Thus the output signal must be 4…20 mA, not
0…20 mA.
4…20 mA
+
-
P
I
...
AI2
AGND
+24V
DGND
OUT
■
DI5 as frequency input
For setting the parameters for the digital frequency input, see the firmware manual.
■
DI6 as PTC input
If DI6 is used as a PTC input, see firmware manual for how to set parameters accordingly.
Note:
If DI6 is used as a PTC input, the wiring and the PTC sensor need to be double
isolated. Otherwise the CMOD-02 I/O extension module must be used.
1
...
+24V
DI6
+
t
°
+
t
°
+
t
°
+
t
°
+
t
°
+
t
°
One to six PTC thermistors connected in series
1
146 Control unit
Summary of Contents for ACQ580-07
