ABB ACH580 Series, Quick Start Up Manual

Page: 3 / 14

EN – Quick start-up guide
This guide describes how to start-up the drive using the First start assistant on the
Hand-Off-Auto control panel. For complete information on start-up, see
ACH580 firmware
manual (3AXD50000027537 [English]).
Note:
Automatic selection of supply voltage is not supported in ACH580-31. You must select the
supply voltage manually using parameter
95.01 . See steps for Commissioning with
parameters on page 9.
Start-up with the First start assistant on an Hand-Off-Auto
control panel
Safety
WARNING!
Do not start-up the drive unless you are a qualified electrician.
Read and obey the instructions in chapter Safety instructions at the beginning of the Hardware manual of the
drive. Ignoring the instructions can cause physical injury or death, or damage to the equipment.
Check the installation. See chapter Installation checklist in the Hardware manual of the drive.
WARNING!
The drive will start up automatically at power-up if the external run command is on and the drive
is in the external control mode.
Check that the starting of the motor does not cause any danger.
De-couple the driven machine if
• there is a risk of damage in case of an incorrect direction of rotation, or
• a
Normal ID run is required during the drive start-up, when the load torque is higher than 20% or the
machinery is not able to withstand the nominal torque transient during the ID run.
Hints on using the assistant control panel
EN – Quick start-up guide 3
R0-
R4
EN
DA
DE
ES
FI
FR
IT
NL
PL
PT
RU
SV
TR
ZH
EN – Quick start-up guide
This guide describes how to start-up the drive using the First start assistant on the
Hand-Off-Auto control panel. For complete information on start-up, see
ACH580
firmware manual (3AXD50000027537 [English]).
Note : Automatic selection of supply voltage is not supported in ACH580-31. You must
select the supply voltage manually using parameter 95.01 . See steps for
Commissioning with parameters on page 9 .
Start-up with the First start assistant on an Hand-Off-Auto
control panel
Safety
Do not start-up the drive unless you are a qualified electrician.
Read and obey the instructions in chapter
Safety instructions at the beginning of the
Hardware manual of the drive. Ignoring the instructions can cause physical injury or death, or
damage to the equipment
Check the installation. See chapter Installation checklist in the Hardware manual of the
drive.
Make sure there is no active start on (DI1 in factory settings, that is, HVAC default).
The drive will start up automatically at power-up if the external run command is on
and the drive is in the external control mode.
Check that the starting of the motor does not cause any danger.
De-couple the driven machine if
• there is a risk of damage in case of an incorrect direction of rotation, or
• a
Normal ID run is required during the drive start-up, when the load torque is higher
than 20% or the machinery is not able to withstand the nominal torque transient during
the ID run.
Hints on using the assistant control panel
The two commands at the bottom of the display
(
Options and Menu in the figure on the right),
show the functions of the two softkeys and
located below the display. The commands
assigned to the softkeys vary depending on the
context.
Use keys
, , and to move the cursor
and/or change values depending on the active
view.
Key shows a context-sensitive help page.
For more information, see
ACX-AP-x assistant
control panels user’s manual (3AUA0000085685
[English]).
?
ACH580 QSG.book Page 3 Friday, September 1, 2017 7:53 PM
The two commands at the bottom of the display ( Options
and Menu in the figure on the right), show the functions of
the two softkeys and located below the display.
The commands assigned to the softkeys vary depending on
the context.
Use keys , , and to move the cursor and/or
change values depending on the active view.
Key shows a context-sensitive help page.
For more information, see ACS-AP-x assistant control panels
user’s manual (3AUA0000085685 [English]).
EN – Quick start-up guide 3
EN