ABB 1ZSC902110-AAA Installation And Commissioning Manual Download

Page: 56 / 84

Installation and commissioning guide

1ZSC000563-AAF EN, REV. 4, 2021-06-23

Dissipation factor, tan δ

The dissipation factor varies with the temperature of the bushing core, and thus the measured dissipation
factor must be multiplied with the correction factor given below.

Bushing core temperature °C

Correction factor to 20 °C (IEC)

0-2

0.80

3-7

0.85

8-12

0.90

13-17

0.95

18-22

1.00

23-27

1.05

28-32

1.10

33-37

1.15

38-42

1.20

43-47

1.25

48-52

1.30

53-57

1.34

57-62

1.35

63-67

1.35

68-72

1.30

73-77

1.25

78-82

1.20

83-87

1.10

Procedure

De-energize the transformer.

Disconnect the external connections from the outer terminal of the bushing.

Remove the cover (58).

G006974

Summary of Contents for 1ZSC902110-AAA





















































































Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands

ABB 1ZSC902110-AAA, Installation And Commissioning Manual

Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands