ABB 1ZSC902110-AAA Installation And Commissioning Manual Download

Page: 68 / 84

Installation and commissioning guide

1ZSC000563-AAF EN, REV. 4, 2021-06-23

11.

Lower the bushing to the floor.

CAUTION!

Make sure that there are support blocks on the floor.

12.

Remove the lifting tool, refer to

Installation of lifting tools,

page

13.

Pull out the upper draw rod (35) and support
tubes (80) by hand.

CAUTION!

Be careful when pulling out the draw
rod. The bushings inside can easily be
damaged.

G00731

14.

Install the lower draw rod (4) in the transport
cover (45).

G004681

15.

Install the transport cover (45) on the transformer turret (46).

End of instruction

7.2 Removal of the bushing from the transformer, fixed bottom contact

Overview

This procedure is only applicable for bushings with a fixed bottom contact.

Procedure

Install the lifting tool, refer to

Installation of lifting tools,

page

Summary of Contents for 1ZSC902110-AAA





















































































Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands

ABB 1ZSC902110-AAA, Installation And Commissioning Manual

Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands