ABB 1ZSC902110-AAA Installation And Commissioning Manual Download

Page: 63 / 84

Installation and commissioning guide
1ZSC000563-AAF EN, REV. 4, 2021-06-23

Procedure

Put a container under the oil valve (51) to collect
oil-spills.

CAUTION!

If transformer oil spills, clean the are
immediately. A wet surface is
dangerous and can cause you to fall.

G006978

Connect the end of a hose to a nipple, and then connect the nipple to the oil valve (51) on the flange.

NOTE!

The thread on the oil valve is (R ½") BSPT ½".

Take the oil sample:

Open (b) the oil valve (51).

Drain a small amount of the transformer oil.

Close (a) the oil valve (51).

G007205

Check the oil-level. If the oil-level is low, refer to

Checking the oil-level,

page

CAUTION!

The oil-level must be above the red
area (29).

NOTE!

It is generally not necessary to fill the
bushing with oil after an oil sample is
taken. But it can be necessary to fill the
bushing with oil when many oil
samples have been taken (3000 ml).

G006767

Summary of Contents for 1ZSC902110-AAA





















































































Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands

ABB 1ZSC902110-AAA, Installation And Commissioning Manual

Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands