ABB 1ZSC902110-AAA Installation And Commissioning Manual Download

Page: 27 / 84

Installation and commissioning guide
1ZSC000563-AAF EN, REV. 4, 2021-06-23

Remove the draw rod nut (10).

NOTE!

The draw rod will fall out of the bushing
if it is not in the horizontal position.

G006961

10.

Pull down the draw rod from the bottom end of the
bushing, and disassemble it at the lower joint (39).

NOTE!

The upper thread (60) is locked with
thread-locking fluid grade 42.

NOTE!

As standard the thread joint (56)
between the draw rod and the bottom
contact is locked with thread-locking
fluid grade 42.

The guiding cone (62) is loose.

G005033

11.

Carefully look for damage at the bottom end of the bushing, and the inside of the center hole.

End of instruction

4.4.2 Installation of the small bottom contact (N1=4) in the transformer

Overview

G005031

40 Small bottom contact

Summary of Contents for 1ZSC902110-AAA





















































































Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands

ABB 1ZSC902110-AAA, Installation And Commissioning Manual

Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands