AAQ AutoLift AL-3000AG Installation Manual & Operation Instructions Download Page 36

Page: 36 / 37

COMMISSIONING REPORT

1. Details of Customer

Customer Name:
Installation Address:

2. Hoist Details

Model No:
Hoist Type:
Installation Date:

3. Commissioning Report

Yes

N/A

Comments

Safety devices incorporated into the design of the vehicle to AS/NZS 1418.9

Visual check all welds completed and comply to requirement of AS/NZS 1554

Visual check carried out for leaks

Safety locks tested for correct operation

Checked for good working order

Supplied with the hoist and in good working order

Checked for correct operation

Hoist checked with load for correct operation and speed control tested

Checked wire ropes for correct installation and tension

Concrete floor is a suitable depth for installation

Safety Devices

Welds

Hydraulic Equipment and Controls

Pneumatic Equipment and Controls

Safety Locks

Support Pads

Wheel Stops

Hoist Motion Limits

Load Test and Speed Check

Wire Ropes

Concrete Floor

2 McDonald Crescent

Bassendean WA 6054

P: 08 9279 1663 | E: [email protected]

Summary of Contents for AutoLift AL-3000AG






































Search results

Summary of Contents for AutoLift AL-3000AG

Reviews:

Related manuals for AutoLift AL-3000AG

Brands by name

Popular brands

AAQ AutoLift AL-3000AG, Installation Manual & Operation Instructions

Search results

Summary of Contents for AutoLift AL-3000AG

Reviews:

Related manuals for AutoLift AL-3000AG

Brands by name

Popular brands