background image

Installation,  Operation  and  Parts  Manual 

AL-

3000AG (FL-8801)

raise 

Overflow valve is loose or jammed. 

Clean or adjust it. 

The gear pump is damaged. 

Replace it. 

Oil level is too low. 

Add oil. 

The oil hose became loose or dropped off. 

Tighten it. 

The cushion valve became loose or jammed. 

Clean or adjusts it. 

Platforms  go  down  slowly 

after being raised 

The oil hose leaks. 

Check or replace it. 

The oil cylinder is not tightened. 

Replace the seal. 

The single valve leaks. 

Clean or replace it. 

The overflow valve leaks. 

Clean or replace it. 

Electrical unloading valve leaks. 

Clean or replace it. 

Raising too slow 

The oil filter is jammed. 

Clean or replace it. 

Oil level is too low. 

Add oil. 

The  overflow  valve  is  not  adjusted  to  the  right 

position. 

Adjust it. 

The hydraulic oil is too hot (above 45°). 

Change the oil. 

The seal of the cylinder is abraded. 

Replace the seal. 

Lowering too slow 

The throttle valve jammed. 

Clean or replace. 

The hydraulic oil is dirty. 

Change the oil. 

The anti-surge valve jammed. 

Clean it. 

The oil hose jammed. 

Replace it. 

TROUBLE SHOOTING 

ATTENTION: If the trouble could not be fixed by yourself, please do not hesitate to contact us for help .We will offer our service at the 

earliest time we can. By the way, your troubles will be judged and solved much faster if you could provide us more details or pictures of 

the trouble.   

TROUBLES 

CAUSE 

SOLUTION 

Motor  does  not  run  and 

will not raise 

The wire connection is loose. 

Check and make a good connection. 

The motor is burnt 

Replace it. 

The  limit  switch  is  damaged  or  the  wire 

connection is loose. 

Connect  it  or  adjust  or  replace  the  limit 

switch. 

Motor  runs  but  will  not  The motor run reversely. 

Check the wire connection. 

Summary of Contents for AutoLift AL-3000AG






































Reviews: