AAON SS1113 Technical Manual Download Page 51

Page: 51 / 62

Main Chiller Controller Technical Guide

APPENDIX A - ECONOMIZER SUBCOOL MODULE LCD SCREENS

Main Screens Map

Refer to the following map when navigating through the LCD Main
Screens. To scroll through the screens, press the

<MENU>

button.

ECON SH1

1809cXXX

SYSTEM
STATUS

ALARMS

Press to scroll through SYSTEM STATUS Screens.

Press to go to SENSOR STATUS Screen.

Press to go to SYSTEM STATUS Screen.

Press to scroll through ECONOMIZER MODULE Screens.

Press to scroll through ALARMS Screens.

Main Screen Map & Module Screens

Module Screens

Refer to the following map when navigating through the RSMV
Screens. From the TBCOR MODULE Screen, press

<ENTER>

scroll through the screens.

ECON SH1

1809cXXX

E-BUS

+###

SOFTWARE

1809cXXX

ADDRESS

# (#)

CURRENT SOFTWARE VERSION

CURRENT BOARD ADDRESS

Conﬁ gure the address according to which circuit

this module represents—1=A, 2=B, 3=C

Number in parentheses is E-BUS address.

Module 1’s address is 95, Module 2’s address 96,

Module 3’s address is 97

E-BUS COMMUNICATION DIAGNOSTICS

Number of COMM packets received.

Press to return to the ECONOMIZER Screen.

Summary of Contents for SS1113






























































Search results

Summary of Contents for SS1113

Reviews:

Brands by name

Popular brands

AAON SS1113, Technical Manual

Search results

Summary of Contents for SS1113

Reviews:

Brands by name

Popular brands