AAON SS1113 Technical Manual Download Page 42

Page: 42 / 62

APPENDIX A - MAIN CHILLER CONTROLLER LCD SCREENS

Main Chiller Controller Technical Guide

Navigation Keys & Main Screens Map

Main Screens Map

Refer to the following map when navigating through the

Main

Screens

. The ﬁ rst screen is an initialization screen. To scroll through

the rest of the screens, press the

<MENU>

button.

TURBOCOR
1807VXXX

Settings

Alarms or
No Alarms

Status

Press to scroll through the

Settings Screens

Press to scroll through the

Status Screens

Press to go to the

Status Screen

Press to go to

Settings Screen

Press to scroll through the Alarms.

Press to return to the ﬁ rst

Main Menu Screen

Press to go to the

Alarms Screen

LCD Display Screen & Navigation

Keys

The LCD display screens and buttons allow you to view status
and alarms, enable force modes, and make BACnet

conﬁ guration

changes. See

Figure 33, below

and refer to

Table 11

for descriptions.

Figure 33: LCD Display and Navigation Keys

Table 11: Navigation Key Functions

NAVIGATION

KEY

KEY FUNCTION

MENU

Use the MENU key to move through
screens within Main Menu categories and
return to the Main Menu while at other
screens.

Use this key to adjust setpoints and change
conﬁ gurations.

DOWN

Use this key to adjust setpoints and change
conﬁ gurations.

ENTER

Use the ENTER key to navigate through the
Main Menu Screen categories.

Summary of Contents for SS1113






























































Search results

Summary of Contents for SS1113

Reviews:

Brands by name

Popular brands

AAON SS1113, Technical Manual

Search results

Summary of Contents for SS1113

Reviews:

Brands by name

Popular brands