AAON SS1113 Technical Manual Download Page 49

Page: 49 / 62

Main Chiller Controller Technical Guide

APPENDIX A - COMPRESSOR CIRCUIT MODULE LED SCREENS

MIN SPD

XXXXRPM

MINIMUM COMPRESSOR SPEED FEEDBACK

RPMs from Turbocor

IGV PERCENTAGE

0-100%

IGV %

XXX

Turbocor Info Screens

Refer to the following map when navigating through the Turbo Info
Screens. From the TURBOCOR INFO Screen, press

<ENTER>

scroll through the screens.

TURBOCOR

INFO

BMC STAT

BMC STATE

BMC Operation Mode:

0=Standby, 1=Levitate, 2=Drive, 3=Calibrate

COMPRESSOR CONTROL STATUS

CONTROL MODE STATES

0 = Levitate Only Mode

1 = Manual Control Mode

2 = Analog Input Mode

3 = ModBus Network Mode

4 = Not Used

SYSTEM STATUS STATES

5 = Locked Out (power cycle required)

6 = IGV/EXV Reset Mode

7 = Ramping Up

8 = Partial Vane Operation

9 = Normal Operation

10 = Maximum Capacity

11 = Minimum IGV

12 = Interlock Open

13 = Fault Reset Mode

14 = Above Drive Temp - waiting to cool down

15 = Compressor Idle

COMPSTAT
BIT0-15=#

Turbocor Info Screen

MAX SPD

XXXXRPM

MAXIMUM COMPRESSOR SPEED FEEDBACK

RPMs from Turbocor

COMM T/O

COMM TIMEOUT TIMER

0 - 30 (if 30, Alarm & Fault)

3PH AMP

3-PHASE AMPERAGE

Three Phase Current Feedback reading

from the Turbocor compressor.

Summary of Contents for SS1113






























































Search results

Summary of Contents for SS1113

Reviews:

Brands by name

Popular brands

AAON SS1113, Technical Manual

Search results

Summary of Contents for SS1113

Reviews:

Brands by name

Popular brands