AAON SS1113 Technical Manual Download Page 43

Page: 43 / 62

Main Chiller Controller Technical Guide

APPENDIX A - MAIN CHILLER CONTROLLER LCD SCREENS

DEVICEID

XXXXXXX

MSTP Baud

38400

BACnet

- CURRENT BAUD RATE

9600, 19200, 38400, 57600, 76800. Default is 38400.

EBUS

Lo Speed or

Hi Speed

E-BUS COMMUNICATIONS

Hi Speed or Lo Speed. Default is Hi Speed.

Settings Screens

BACnet

- CURRENT DEVICE ID

A Device ID of up to 7 digits can be entered.

The

<ENTER>

key moves the cursor between the digit ﬁ elds starting

with the ones ﬁ eld. Once the cursor is under a ﬁ eld, use the

<UP>

<DOWN>

arrow keys to select a number between 0 and 9.

Settings Screens

Refer to the following map when navigating through the Settings
Screens. From the

Settings Screen

, press

<ENTER>

to scroll through

the screens.

Settings

MAC Addr
0 TO 127

BACnet

- CURRENT MAC ADDRESS

Valid range is 0 to 127. Default is 1.

The

<ENTER>

key moves the cursor between the digit ﬁ elds starting

with the ones ﬁ eld. Once the cursor is under a ﬁ eld, use the

<UP>

<DOWN>

arrow keys to select a number between 0 and 9.

Unit ID#

Addr #1-59

UNIT ADDRESS

Unit address. Valid range is 1-59. Default is 59.

485 Baud

Lo-Speed or

Hi-Speed

BAUD RATE SPEED

485 baud rate speed. Valid range is Lo-Speed or Hi-Speed.

Default is Hi-Speed.

Summary of Contents for SS1113






























































Search results

Summary of Contents for SS1113

Reviews:

Brands by name

Popular brands

AAON SS1113, Technical Manual

Search results

Summary of Contents for SS1113

Reviews:

Brands by name

Popular brands