A-Link WNAP User Manual Download Page 28

Page: 28 / 102

USER’S MANUAL OF WNAP 3G MOBILE ROUTER

Version: 2.0

3.3.5

Wireless - Advanced Settings

These settings are only for more technically advanced users who have a

sufficient knowledge about wireless LAN. These settings should not be changed

unless you know what effect the changes will have on your WNAP 3G Mobile

Router.

Screen snapshot – Wireless Advanced Settings

Item

Description

Fragment Threshold

Set the data packet fragmentation threshold, value can be written

between 256 and 2346 bytes.

Refer to 4.10 What is Fragment Threshold?

RTS Threshold

Set the RTS Threshold, value can be written between 0 and 2347

bytes.

Refer to 4.11 What is RTS(Request To Send) Threshold?

Beacon Interval

Set the Beacon Interval, value can be written between 20 and 1024

ms.

Refer to 4.12 What is Beacon Interval?

Preamble Type

Click to select the

Long Preamble

Short Preamble

support on the

Summary of Contents for WNAP







































































































Search results

Summary of Contents for WNAP

Reviews:

Related manuals for WNAP

Brands by name

Popular brands

A-Link WNAP, User Manual

Search results

Summary of Contents for WNAP

Reviews:

Related manuals for WNAP

Brands by name

Popular brands