A-Link WNAP User Manual Download Page 48

Page: 48 / 102

USER’S MANUAL OF WNAP 3G MOBILE ROUTER

Version: 2.0

Refer to 4.22 What is Universal Plug and Play (uPNP)?

Enable IGMP Proxy

Click the checkbox to enable IGMP Proxy.

Enable Ping Access on

WAN

Click the checkbox to enable WAN ICMP response.

Enable Web Server Access

on WAN

Click the checkbox to enable web configuration from WAN side.

Enable FTP Server Access

on WAN

Click the checkbox to enable FTP Server Access on WAN

Enable IPsec pass through

on VPN connection

Click the checkbox to enable IPSec packet pass through

Enable PPTP pass through

on VPN connection

Click the checkbox to enable PPTP packet pass through

Enable L2TP pass through

on VPN connection

Click the checkbox to enable L2TP packet pass through

Apply Changes

Click the

Apply Changes

button to complete the new configuration

setting.

Reset Click

the

Reset

button to abort change and recover the previous

configuration setting.

Summary of Contents for WNAP







































































































Search results

Summary of Contents for WNAP

Reviews:

Related manuals for WNAP

Brands by name

Popular brands

A-Link WNAP, User Manual

Search results

Summary of Contents for WNAP

Reviews:

Related manuals for WNAP

Brands by name

Popular brands