A-Link WNAP User Manual Download Page 76

Page: 76 / 102

USER’S MANUAL OF WNAP 3G MOBILE ROUTER

Version: 2.0

3.3.28

Management - Time Zone Setting

This page is used to configure NTP client to get current time.

Screen snapshot – Management – Time Zone Settings

Item

Description

Current Time

It shows the current time.

Time Zone Select

Click the time zone in your country.

Enable NTP client update

Click the checkbox to enable NTP client update. Refer to 4.26 What

is NTP Client?

Automatically Adjust

Daylight Saving

Click to enable Daylight Saving adjustment automatically.

NTP Server

Click select default or input NTP server IP address.

Apply Change

Click the

Apply Changes

button to save and enable NTP client

service.

Reset Click

the

Reset

button to abort change and recover the previous

configuration setting.

Refresh

Click the refresh the current time shown on the screen.

Summary of Contents for WNAP







































































































Search results

Summary of Contents for WNAP

Reviews:

Related manuals for WNAP

Brands by name

Popular brands

A-Link WNAP, User Manual

Search results

Summary of Contents for WNAP

Reviews:

Related manuals for WNAP

Brands by name

Popular brands