A-Link WNAP User Manual Download Page 14

Page: 14 / 102

USER’S MANUAL OF WNAP 3G MOBILE ROUTER

Version: 2.0

mobile stations.

Step 2: Connect the WNAP 3G Mobile Router to your wired network. Connect the

Ethernet WAN interface of WNAP 3G Mobile Router by category 5 Ethernet

cable to your switch/ hub/ xDSL modem or cable modem. A straight-through

Ethernet cable with appropriate cable length is needed. Or you can connect your

3G USB modem to WNAP USB port.

Step 3: Supply DC power to the WNAP 3G Mobile Router. Use only the AC/DC power

adapter supplied with the WNAP 3G Mobile Router; it maybe occur damage by

using a different type of power adapter.

The hardware installation finished.

2.2

Software Installation

There is no software drivers, patches or utilities installation needed, but only the

configuration setting. Please refer to chapter 3 for software configuration.

Notice:

It will take about 50 seconds to complete the boot up sequence after

powered on the WNAP 3G Mobile Router; Power LED will be active,

and after that the WLAN Activity LED will be flashing to show the

WLAN interface is enabled and working now.

Summary of Contents for WNAP







































































































Search results

Summary of Contents for WNAP

Reviews:

Related manuals for WNAP

Brands by name

Popular brands

A-Link WNAP, User Manual

Search results

Summary of Contents for WNAP

Reviews:

Related manuals for WNAP

Brands by name

Popular brands