A-Link WNAP User Manual Download Page 60

Page: 60 / 102

USER’S MANUAL OF WNAP 3G MOBILE ROUTER

Version: 2.0

Enable PPTP pass through

on VPN connection

Click the checkbox to enable PPTP packet pass through

Enable L2TP pass through

on VPN connection

Click the checkbox to enable L2TP packet pass through

Apply Changes

Click the

Apply Changes

button to complete the new configuration

setting.

Reset Click

the

Reset

button to abort change and recover the previous

configuration setting.

Keep Alive HSPA - Advanced

Screen snapshot – WAN Interface Setup – GSM 3.5G – Advanced

Item

Description

Advanced

You can modify keep alive HSPA settings manually.

IP address for ping. It is recommended to use IP address always

available.

Ping Interval

Interval time between pings. Choose between 1 to 7 seconds

depending of your 3G modem.

Packet Size

Packet size for ping.

Summary of Contents for WNAP







































































































Search results

Summary of Contents for WNAP

Reviews:

Related manuals for WNAP

Brands by name

Popular brands

A-Link WNAP, User Manual

Search results

Summary of Contents for WNAP

Reviews:

Related manuals for WNAP

Brands by name

Popular brands