3onedata MES600 Series User Manual Download Page 72

Page: 72 / 76

Industrial Ethernet Switch User Manual

3onedata proprietary and confidential

14.4 Indicator Problem

Power indicator isn't bright, what's the reason?

Possible reasons include:

Not connected to the power socket; troubleshooting, connected to the

power socket.

Power supply or indicators faults; troubleshooting, change the power

supply or device test.

Power supply voltage can't meet the device requirements; troubleshooting,

configure the power supply voltage according to the device manual.

Link/Act indicator isn't bright, what's the reason?

Possible reasons include:

The network cable portion of Ethernet copper port is disconnected or bad

contact; troubleshooting, connect the network cable again.

Ethernet terminal device or network card works abnormally; troubleshooting,

eliminate the terminal device fault.

Not connected to the power socket; troubleshooting, connected to the

power socket.

Interface rate doesn't match the pattern; troubleshooting, examine whether

the device transmission speed matches the duplex mode.

Ethernet copper port and fiber port indicator are connected normally, but

can't transmit data, what's the reason?

When the system is power on or network configuration changes, the device and

switch configuration in the network will need some time. Troubleshooting, after

the device and switch configuration are completed, Ethernet data can be

transmitted; if it's impassable, power off the system, and power on again.

The switch halts after communicate for a period time, and returns to normal

after reboot, what's the reason?

Reasons may include:

Surrounding environment disturbs the product; troubleshooting, product

grounding adopts shielding line or shields the interference source.

Summary of Contents for MES600 Series













































































Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands

3onedata MES600 Series, User Manual

Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands