3onedata MES600 Series User Manual Download Page 51

Page: 51 / 76

Industrial Ethernet Switch User Manual

3onedata proprietary and confidential

Defines MIB view of community name.

Setup visit privilege of MIB objective is Write or Read. Community name

with Read privilege can check the device information only. Community

name with Write privilege can configure the device.

Setup appointed basic visit control list of the community name.

Switch supports SNMP V1/V2c. Both SNMP V1 and V2c use public character

strings for match authentication.

SNMP usually uses UDP Port 161(SNMP) and 162 (SNMP-traps) based on

TCP/IP protocol. SNMP protocol agent is existed in network device. MIB

(information specific to the device) is uses as device connector. These network

devices can be monitored or controlled through the agent. When trap event

happens, a message is transmitted by SNMP Trap, an available trap receiver can

get this trap information.

SNMP supports 3 kinds of basic operating in total:

Get:

Manager can use this to get some variable value of Agent.

Set:

Manager can use this to set up some variable value of Agent.

Trap:

Agent uses this to send an alarm to manager.

Read Community

Use a character string to name a SNMP community. This community only has Get

privilege.

Read/Write Community

Summary of Contents for MES600 Series













































































Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands

3onedata MES600 Series, User Manual

Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands