3onedata MES600 Series User Manual Download Page 58

Page: 58 / 76

Industrial Ethernet Switch User Manual

3onedata proprietary and confidential

11.3 Traffic Statistics

Number of bytes of all data packets sent by the port

Number of bytes of all data packets received by the port

Unicast

Number of unicast data packets sent and received by the port

Multicast

Number of multicast data packets sent and received by the port

Broadcast

Number of broadcast data packets sent and received by the port

Error

Number of error packets because of some reasons sent and received by the port

11.4 MAC address table

MAC

（

Media Access Control

）

address is the network device hardware identification,

the switch to forward packets based on MAC addresses. The MAC address is unique,

which ensures correct packet forwarding. Each switch maintains a MAC address table.

In this table, MAC addresses and switches port one-to-one correspondence. When

the switches received a data frame, according to the MAC address table to determine

Summary of Contents for MES600 Series













































































Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands

3onedata MES600 Series, User Manual

Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands