3onedata MES600 Series User Manual Download Page 43

Page: 43 / 76

Industrial Ethernet Switch User Manual

3onedata proprietary and confidential

LLDP

8.1 Parameter Configuration

LLDP is a second layer topology discovery protocol, the basic principle is: network

equipment to the adjacent equipment issued its notice of state information, and each

port of all equipment are stored with their own information, if a local device state

changes, also can with its directly connected neighbor devices to send updated

information to that neighbor devices will be the information stored in the standard

SNMP-MIB library. Network management system can query from the SNMP-MIB

Library of the current second layer connection. It should be noted that LLDP is only a

remote device status information discovery protocol, it can’t complete the network

device configuration and port control and other functions.

Configuration item meaning

Disable

The switch will not send the LLDP message, and will reduce the

LLDP message received from the neighbor.

Enable

The switch will send the LLDP message, which will analyze the

LLDP message received from the neighbor.

TX interval

The switch status is not changed, the device periodically to the

neighbor nodes to send LLDP packets, the interval time is

called to send LLDP message interval.

Switch will not send out the LLDP information, but the

information from the vicinity of the unit LLDP analysis.

Will reduce the LLDP information received from the neighbors,

but will send LLDP information.

Summary of Contents for MES600 Series













































































Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands

3onedata MES600 Series, User Manual

Search results

Summary of Contents for MES600 Series

Reviews:

Related manuals for MES600 Series

Brands by name

Popular brands