11
K:2
Remove existing liner(s) and insert new foam liner(s).
K:3
Fit one side of the ear cushion into the groove of the
earcup and then press on the opposite side until the ear
cushion snaps in place.
REPLACING THE HARD HAT ATTACHMENT PLATE
For proper fitting on different industrial safety hard hats, the
hard hat attachment plate may need to be replaced. The
headset comes assembled with P3E hard hat attachment.
Plates for P3K hard hat attachment assembly are also
included in the box, while other plates can be obtained from
your dealer. A screwdriver is needed to replace the hard hat
attachment plate.
M:1
Loosen the screw holding the plate and remove the
plate.
M:2
Attach the appropriate plate while ensuring the left
(L) and right (R) designated plates are on the appropriate
earmuff, if applicable, and then tighten the screw.
FCC AND IC INFORMATION
FCC Warning
This device complies with part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation. Any Chan-
ges or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment. Before any station transmits on any
channel authorized in the GMRS from a point (a geographical
location) within or over the territorial limits of any area where
radio services are regulated by the FCC, the responsible
party must obtain a license (a written authorization from the
FCC for a GMRS system).
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This transmitter
must not be co-located or operating in conjunction with any
other antenna or transmitter. Do not transmit for more than
50% of the total transceiver use time; transmitting over 50%
of the total use time may exceed the limits in accordance to
the FCC RF exposure requirements. Nominal transceiver
operation is 5% transmission time, 5% reception time and
90% stand-by time.
IC Warning
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions: This device may not
cause interference. This device must accept any interference,
including interference that may cause undesired operation of
the device.
SPARE PARTS AND ACCESSORIES
3M™ PELTOR™ HY79 Hygiene kit
Replaceable hygiene kit consisting of two attenuation cushi-
ons, two foam rings and two snap-in ear cushions. Replace
at least twice a year to ensure constant attenuation, hygiene
and comfort.
3M™ PELTOR™ HY100A Single-use protectors
A single-use protector that is easy to fit to the ear cushions.
Pack of 100 pairs.
3M™ PELTOR™ HYM1000 Microphone protector
Moisture-resistant and wind-resistant hygienic tape that
protects the speech microphone and extends its life at the
same time. Pack of 5 meters (16 feet) is sufficient for around
50 replacements.
3M™ PELTOR™ M995 Wind shield for electret microp-
hone
Effective protection from wind noise for electret microphone
that also protects it and extends its life. One protector per
pack.
3M™ PELTOR™ ACK053 Rechargeable battery
NiMH rechargeable battery that can replace two AA type 1.5
V standard batteries.
3M™ PELTOR™ FR08 Power supply
Power supply for FR09/ACK053.
3M™ PELTOR™ FR09 Battery charger
Charger for ACK053.
3M™ PELTOR™ 1180 SV Battery cover
3M™ PELTOR™ MT53N-12 Electret microphone
Supplied as standard with product.
CAN ICES-3 (B)/NMB-3(B)
WARRANTY AND LIMITATION OF LIABILITY
WARRANTY: In the event any 3M Personal Safety Division
product is found to be defective in material, workmanship, or
not in conformity with any express warranty for a specific pur
-
pose, 3M’s only obligation and your exclusive remedy shall
be at 3M’s option, to repair, replace or refund the purchase
price of such parts or products upon timely notification of the
issue by you and substantiation that the product has been
stored, maintained and used in accordance with 3M’s written
instructions. EXCEPT WHERE PROHIBITED BY LAW,
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY
EXPRESS OR IMPLIED WARRANTY OF MERCHANTABIL
-
ITY, FITNESS FOR A PARTICULAR PURPOSE OR OTHER
WARRANTY OF QUALITY, OR THOSE ARISING FROM A
COURSE OF DEALING, CUSTOM OR USAGE OF TRADE,
EXCEPT OF TITLE AND AGAINST PATENT INFRINGE-
MENT. 3M has no obligation under this warranty with respect
to any product that has failed due to inadequate or improper
storage, handling, or maintenance; failure to follow product
instructions; or alteration or damage to the product caused by
accident, neglect, or misuse.
EN