3Disc Heron IOS User Manual Download Page 56

Page: 56 / 72

Page 56

User Manual

Step-by-Step Procedure

Step 1:

Clean the tip with soapy water, ensuring that the mirror

is clean and free of smudges, stains, or any residue. Avoid using

abrasive cloth materials as this will scratch the mirror.

Step 2

: After drying the tip exterior, carefully dry the interior and

mirror with lint free wipes ensuring you do not scratch the sur-

face. The mirror should be free of any noticeable debris or water

spots.

Step 3:

Insert and seal the tip into a sterilization pouch. Make

sure the seal is airtight. Each tip should be packaged

individually.

Step 4:

Sterilize the wrapped tip in a steam autoclave at follow-

ing parameters:

•

132°C (270°F) at 4 minutes, or

•

134°C (273°F) at 4 minutes, or

•

121°C (250°F) at 45 minutes

Step 5:

Ensure the dry cycle is complete prior to removing the

tip from the autoclave. If the pouch is damp with moisture,

proper sterilization cannot be guaranteed

NOTE

: Tips should not be placed in an ultrasonic cleaner or any

cold sterile solutions. The sterilant solutions will leave a sticky

residue or film on the mirror when drying

WARNING: Do not autoclave the handpiece of the device.

WARNING

: Always autoclave the tip wrapped in a sealed

sterilization pouch; failure to do so will result in permanent stains

on the mirror.

Summary of Contents for Heron IOS









































































Search results

Summary of Contents for Heron IOS

Reviews:

Brands by name

Popular brands

3Disc Heron IOS, User Manual

Search results

Summary of Contents for Heron IOS

Reviews:

Brands by name

Popular brands