manualshive.com logo in svg

3D Systems SLA 750 Series, User Manual, Page: 91 / 101

Share
Download
3D Systems SLA 750 Series User Manual Download Page 91

11

  SLA 750 SERIES PREVENTATIVE MAINTENANCE

11.1  Recoating blade

11.1.1  Cleaning

The recoater blade will need to be cleaned periodically. Remove the recoater blade (see 

Recoater Installation and Removal

section in User Guide) and wipe it off using a paper towel soaked with isopropyl alcohol. Be careful not to contaminate the

material in the vat with the isopropyl alcohol. Be sure to wear nitrile gloves when handling the recoater blade. Do not use any

items which may cause physical damage to the recoater blade. Nonmetallic items, such as a wooden tongue depressor or soft

plastic implement, can be used to remove heavy debris. Wipe the recoater blade dry when finished.

11.1.2  Resin Blade vacuum Level Adjustment

Setting and Verifying Resin Blade Level

1. Select Level Material from the Elevator & Recoater menu.
2. Toggle Vacuum to the On position from the Recoater Settings section
3. Select Level Material again.
4. Move the recoater blade to a position where the blade window is easily accessible and observable by toggling the Back icon

from the Recoater section.

5. The below illustration is the ideal resin level displayed in the window. Ideal resin level should be 1/4 to 1/3 the way up into

the sight window.

1. If resin level is too high or too low, move to the following steps.
2. Unlock doors from the UI and open front door. This will cause the vacuum to stop.
3. Located inside right of the printer are the the Coarse and Fine adjustment knobs.
4. Start by turning the Coarse adjustment a quarter turn.

3D Systems, Inc.

87

p/n 40-D150, Rev. C

Summary of Contents for SLA 750 Series






































































































Reviews:

No comments