manualshive.com logo in svg

3D Systems SLA 750 Series, User Manual, Page: 60 / 101

Share
Download
3D Systems SLA 750 Series User Manual Download Page 60

A

DHCP - a network protocol that enables a server to automatically assign an IP address to a computer from a defined

range of numbers (i.e., a scope) configured for a given network. Uncheck this box to enable editing of the IP Address,

Subnet Mask, Gateway, and DNS Servers.

B

MAC Address - A hardware address for the network adapter in the printer's computer. For display only. This number

cannot be changed through this interface.

C

IP Address - The numerical address given to your printer on your network. For display only. This number cannot be

changed through this interface.

D

Subnet Mask - hides, or "masks," the network part of a system's IP address and leaves only the host part as the

machine identifier. Contact your network administrator if there is a need to change this number.

E

Gateway - a router interface connected to the local network that sends packets out of the local network. For display

only. This number cannot be changed through this interface.

3D Systems, Inc.

56

p/n 40-D150, Rev. C

Summary of Contents for SLA 750 Series






































































































Reviews:

No comments