manualshive.com logo in svg

3D Systems SLA 750 Series, User Manual, Page: 20 / 101

Share
Download
3D Systems SLA 750 Series User Manual Download Page 20

4

Emergency Stop (E-Stop): This switch is located on the side panel above the touch screen. The E-Stop immediately

disables all motion controls and the laser, rendering them safe. After being pressed, it remains in the closed state

until it is manually returned to the open state by pulling the red knob and turning it clockwise. An E-Stop is also

located inside the print chamber.
System Status Lights: System Status Lights indicate critical information regarding the system. See the section, "LED

Indicators" for descriptions of each indicator.

5

User Interface (UI): This is the 15.6" control touchscreen which allows the user to interface with the printer. The

touchscreen enables the user to view and adjust the print parameters used to print a part as well as control the

various hardware components of the printer.

6

RDM (Resin Delivery Module): The RDM is a gravity fed system.

7

Master Power Shut-of switch: The SLA 750 has a master circuit breaker switch located on the electrical cabinet

module on the right side of the machine.

Dual-Laser Setup
The dual-laser version of the machine will have the same components as seen above, as well as an additional Laser Assembly.

The two lasers are referred to as A-side and B-side.

3D Systems, Inc.

16

p/n 40-D150, Rev. C

Summary of Contents for SLA 750 Series






































































































Reviews:

No comments