3Com 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print Server User Manual Download Page 55

Page: 55 / 94

Internet Printing Protocol (IPP)

Figure 29

Windows 2000 - Locate your Printer

Select

Connect to a printer on the Internet or on your Intranet

, and enter

the URL of the IPP Server as follows:

Port 1 ip_address:631/ipp/P1

where

ip_address

represents the IP Address of the IPP Server, and 631

is the port number.

These entries are case sensitive. They must be entered as shown, with

ipp

in lower case, and P1 in UPPER case.

If the connection can be established, and the printer on that port is
on-line, the following dialog will be displayed.

Figure 30

Windows 2000: No printer driver

Click

, and then select the printer manufacturer and model to match

the printer connected to the port on the IPP Server.

Click

Next

, and complete the Wizard.

The IPP printer is now ready for use.

Summary of Contents for 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print Server































































































Search results

Summary of Contents for 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print Server

Reviews:

Related manuals for 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print Server

Brands by name

Popular brands

3Com 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print Server, User Manual

Search results

Summary of Contents for 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print Server

Reviews:

Related manuals for 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print Server

Brands by name

Popular brands