manualshive.com logo in svg

ZyXEL Communications ZyXEL Prestige 310, Руководство пользователя

Поделиться
Скачать
ZyXEL Communications ZyXEL Prestige 310 Скачать руководство пользователя страница 27

Prestige 310 Broadband Sharing Gateway

1-4

Getting to Know Your Prestige

you can enter the time manually but each time the system is booted, the time & date will be reset to 1/1/1970
0:0:0.

1.2.19 Logging and Tracing

•

 

Built-in message logging and packet tracing.

•

 

Unix syslog facility support.

1.2.20 Embedded FTP and TFTP Servers

The Prestige's embedded FTP and TFTP servers enable fast firmware upgrades as well as configuration file
backups and restoration.

1.2.21 Packet Filtering

The Packet Filtering mechanism blocks unwanted traffic from entering/leaving your network.

1.2.22 Upgrade Prestige Firmware via LAN

The firmware of your Prestige can be upgraded via the LAN.

1.3  Applications for the Prestige 310

1.3.1  Broadband Internet Access via Cable or DSL Modem

A cable modem or xDSL modem can connect to the Prestige 310 for broadband Internet access via Ethernet
port on the modem.  A typical Internet access application is shown next.

Figure 1-1 Internet Access Application

Содержание ZyXEL Prestige 310








































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды