ZURN Aquaflush Z6000 Скачать руководство пользователя страница 84

Страница: 84 / 89

Page 4 of 9

Operation and Maintenance Manual

7000 Apple Tree Avenue, Bergen, NY 14416 Phone: (800) 543-2550-Fax: (585) 494-1839-www.libertypumps.com

DWG#7235000I

Manual 7235000I

Operation and Maintenance Manual

Before proceeding with the installation or operation of the Oil Tector Remote Alarm, read all

instructions thoroughly, as well as complying with all Federal, State and Local Codes, Regulations

and Practices. The Oil Tector Remote Alarm must be installed by qualified personnel familiar with

all applicable local electrical and mechanical codes. Refer to the National Electrical Code (NFPA

70). Failure to properly install and test this product can result in personal injury or equipment

malfunction.

Introduction

Safety Guildlines

1. DO NOT USE WITH FLAMMABLE OR EXPLOSIVE FLUIDS SUCH AS GASOLINE, FUEL OIL, KEROSENE, ETC.

DO NOT USE IN EXPLOSIVE ATMOSPHERES.

2. REMOTE ALARM MUST BE MOUNTED INDOORS. FOR OUTDOOR APPLICATIONS CONSULT FACTORY.

Description of Operation

The OIL TECTOR REMOTE ALARM is powered by 120 VAC coming from standard wall outlets and is transformed to

11 VDC. Installing a 9 Volt battery provides battery back-up.

Tools, Supplies and Requirements for Installation (Not Included)

#1. Phillips screw driver

#2. (Qty 2) #6 self tapping screws

#3. Access to 120 VAC power receptacle

#4. Optional \ plastic anchor if mounting to sheet rock

#5. Optional 9V battery (used for battery back up if power goes out)

#6. Optional Wire stripper (used if you need to strip wire to connect to a BAS or SCADA system)

#7. Optional needle nose pliers if using aux contacts

The Oil Tector Remote Alarm activates on High Oil or High Water from the control panel. Seperate dry contacts for High

Oil and High Water can be connected to an Auto Dialer, a BAS (building automation system) or SCADA system.

Содержание Aquaflush Z6000


























































































Результаты поиска

Содержание Aquaflush Z6000

Отзывы:

Похожие инструкции для Aquaflush Z6000

Бренды по названию

Популярные бренды

ZURN Aquaflush Z6000, Инструкция по установке, эксплуатации, обслуживанию и каталог запасных частей

Результаты поиска

Содержание Aquaflush Z6000

Отзывы:

Похожие инструкции для Aquaflush Z6000

Бренды по названию

Популярные бренды