ZONGSHEN ZS250GY-3 Скачать руководство пользователя

Страница: 73 / 76

LIS

2.9 Analysis of electric horn

E l e c t r i c h o r n c a n n o t

make sound.

Turn on ignition switch,turn on/off turning light switch

and check the turning light.

Turning light cannot illuminate or

illuminate dimly.

T u r n i n g l i g h t c a n

illuminate brightly.

The power of storage battery is

not enough or the circuit between

storage battery and ignition switch

has open circuit or short circuit.

Power supply of storage

battery is normal.

Remove the power lead from the power

connection of electric horn,then rub the

power lead with cathode wire.Check

the spark or measure the voltage with

multimeter.

When rubbing,there is spark

or the voltage is normal.

When rubbing,there is no spark or

the voltage is not normal.

The power wire between

ignition switch and electric

horn has open circuit.

Connect the power lead of electric horn.

Connect the non-power connection of

electric horn(connection of button)with

the cathode wire.

After connection,the electric horn

can make sound.

After connection,the electric horn

still cannot make sound.

The inner connecting point of horn

has bad connection or the lead

between electric horn and button

has open circuit.

Adjust the volume and tone of

electric horn.

After adjustment,electric horn

still cannot make sound.

After adjustment,the horn

sound is normal.

Electric horn is

damaged.

Electric horn is adjusted

unproperly.

Содержание ZS250GY-3













































































Результаты поиска

Содержание ZS250GY-3

Отзывы:

Похожие инструкции для ZS250GY-3

Бренды по названию

Популярные бренды

ZONGSHEN ZS250GY-3, Руководство по обслуживанию

Результаты поиска

Содержание ZS250GY-3

Отзывы:

Похожие инструкции для ZS250GY-3

Бренды по названию

Популярные бренды