ZONGSHEN ZS250GY-3 Скачать руководство пользователя

Страница: 55 / 76

LIS

Section 3 Control Part

1 Composing and Function of Control Part

In electrical system of motorcycle,control part is to ensure the good working condition of power supply

part and power consumption part,and ensure their harmony.It can make rider control the electrical system

momentarily.

Control part mainly consists of adjuster,rectifier,flash relay,starting relay,fuse tube,control switch and

cable assembly.

(1)Adjuster

Adjuster is the important component of power supply part of motorcycle electrical system.It can be

divided into DC generator adjuster and AC generator adjuster according to the engine type.

[1]DC generator adjuster

Because the voltage export of DC generator adjuster and the rev has direct proportion,it will bring some

problems:[A]When motorcycle runs with high speed,the engine rev is very fast and the voltage export of

DC generator is very high,which will easily make the electro-equipment burn out and make the storage

battery over charge.[B]When motorcycle runs with low speed,the engine rev is very low,which makes

storage battery export power to DC generator with strong electric current so that the DC generator is burned

out.So it is necessary to make adjuster cooperate with generator.

[2]AC generator adjuster

The motorcycle with generator not only needs the rectifier to transfer the AC to DC,but also it needs

AC adjuster to stabilize the export of generator.At present,the AC adjuster which is usually used is AC

electronic adjuster.

AC adjuster mainly consists of transistor,diode and thyristor.When generator works,the lighting and

signal coil will produce AC.

(2)Rectifier

Rectifier is normally divided into two types:single-phase half wave rectifier and full-wave bridge

rectifier.These two rectifiers work as the principle of one-way electric character of silicon diode.It is like an

electronic valve,which only allows one side electric current to go through.

(3)Flash Relay

Flash relay is called flasher.It is mainly divided into three types:thermal resistance,capacitance and

transistor.

(4)Starting Relay

When starting electromotor works,the electric current will be very strong.It can reach tens of amp.

Starting relay is an electromagnetic switch.When pressing the starting switch of right handlebar,electric

current will connect with the cathode of battery through storage battery,battery connection,relay coil and

connection of starting switch,then it will make a closed circuit.

(5)Tube

Generally, fuse is composed of plastic fuse boxes fitted up with the fuse tube.

(6)Control Switch

The control switches of electrical system are centralized on the left and right handlebar.Normally,from

up to down,there are switches of high/low beam light,turning light and horn on the left handlebar.Also,from

up to down,there are switches of position light,headlight and electric starter on the right handlebar.The

general electrical switch is in the middle of handlebar.

(7)Main Cable

Each part of electrical system of motorcycle is connected by lead.In order to avoid leads in a mess

and be propitious to arrange on the frame,leads with the same direction are usually bound by insulative

rubberized fabric.This is cable assembly.

[1]Measure the voltage expor t of relay with

multimeter and check whether it is within 13.0V

～

14.0V.Replace the voltage -adjusting relay when

the voltage export is lower than 13.0V.

2 Disassembly and Maintenance of Control Part

Joint of voltage-

adjusting relay

Replace the rectifier when the cooling fins of it

are broken.

CAUTION

Содержание ZS250GY-3













































































Результаты поиска

Содержание ZS250GY-3

Отзывы:

Похожие инструкции для ZS250GY-3

Бренды по названию

Популярные бренды

ZONGSHEN ZS250GY-3, Руководство по обслуживанию

Результаты поиска

Содержание ZS250GY-3

Отзывы:

Похожие инструкции для ZS250GY-3

Бренды по названию

Популярные бренды