ZONGSHEN ZS250GY-3 Скачать руководство пользователя | Manualshive

Страница: 7 / 76

background image

EN

G

LIS

H

3

proper pull and speed of motorcycle,so that it can adapt the changable running condition.The gearshift of
this motorcycle adopts gradational gearshift.

[4]Rear transmission device
The function of rear transmission device is to transmit the engine power to transmission device,so that

the rev is reduced and the torque is augmented.Then transmit the power to rear wheel to drive motorcycle
run.The transmission of this motorcycle is chain transmission.

[5]Intake and Exhaust System
The function of inlet system is to guide and filtrate air,to control the volume of mixed gas flowing into

cylinder according to the needs of working condition.It mainly consists of inlet pipe and air cleaner.

The function of exhaust system is to vent the exhaust gas in cylinder and to reduce the noise during

exhausting.It mainly consists of exhaust pipe and muffler.

4 Fuel Supply System

The function of fuel-supplying system is to confect clean gas and air into mixed gas with proper

proportion according to the working condition of engine,and to offer the mixed gas timely and
quantificationally to burning chamber to keep burning.

The fuel supply system mainly consists of fuel tank,fuel pump,fuel injector,fuel filter and fuel pipe.

5 Electrical System

The function of electrical system is to offer electric power to the starting and running of motorcycle,and

to send sound or light signals so that the running safety can be ensured.The electrical system mainly
contains the part of electric power supply,electric power consumption and electric power control.

[1]Electric Supply
The part of electric supply mainly consists of generator and battery.When generator reaches a certain

rev driven by engine,generator will export eletric power,which not only offers the power to electric
setup,but also to the battery so that it can be charged. The battery can transfer chemical power to electric
power,which can support starting,illumination and signal setup.

[2]Electric Consumption
The function of electric consumption part is to offer several kinds of sound or light signals to ensure

running safety,meanwhile it can start engine conveniently and fast.It mainly consists of illuminating signal
device and electric starter device.

[3]Control Part
The function of control part is to ensure and adjust electric supply and electric consumption.It mainly

consists of ECU,rectifier,starter relay,fuse

，

control switch and main wire.

6 Engine

Engine is a device,which is to make fuel burn in the cylinder and to transfer heat to mechanical power.

it is the power producer of motocycle.(The maintenance of engine please refer to the engine service
manual)

«
...
5
6
7
8
9
...
»

Содержание ZS250GY-3













































































Отзывы:

Нет отзывов

Похожие инструкции для ZS250GY-3

Бренд: X-lite Страницы: 6

WARRIOR YFM350XS

Бренд: Yamaha Страницы: 46

Бренд: Yamaha Страницы: 102

Бренд: National Cycle Страницы: 2

Бренд: Victory Motorcycles Страницы: 332

Бренд: Honda Страницы: 102

Бренд: MRA Страницы: 8

Бренд: AC Schnitzer Страницы: 44

Бренд: Honda Страницы: 93

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 63

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 94

Star XV1900AE 2013

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды