ZONGSHEN ZS250GY-3 Скачать руководство пользователя

Страница: 33 / 76

LIS

Front shock absorber is the spring connecting part between front wheel and vehicle body.Rear shock

absorber mainly bear axial pressure of rear wheel.Both of them support the weight of the whole vehicle
body.During motorcycle running,it reduces the concussion and shake for motorcycle and rider,reduces the
pressure for components,prolongs the service lifetime of motorcycle and enhances the comfort,operation
and stability for rider.

Section 8 Shock Absorber

1 The Structure and Working principle of Front/Rear Shock Absorber

2 Disassembly and Maintenance of Front Shock Absorber

[1]Front Shock Absorber

The front shock absorber of this motorcycle adopts compound of hydraulic pressure and spring.It

mainly consists of front shock absorber spring,seal ring,dustproof cover,piston ring,front shock absorber

pole,piston lever,buffer spring,one-way valve spring socket,one-way valve spring,one-way valve,one-way

valve socket,front shock absorber pipe and piston lever socket.

When the front wheel of motorcycle gets strike and shake,the front shock absorber pipe rises,the

damping oil flows up through the one-way valve and small holes on piston lever.The resistance power is

small at this time.When absorber pipe continues going up,the clearance between one-way valve socket

and the cone-shaped surface of piston lever becomes smaller and smaller,so that the resistance becomes

bigger,which avoids the bump of front shock absorber pipe and front shock absorber.When front shock

absorber pipe goes down for the returning of front shock absorber spring,the damping oil only can flow

from the small holes of piston lever because of the close of one-way valve,which causes a big resistance,so

that it reduces the shake of front shock absorber spring.

[2]Rear Shock Absorber

The rear shock absorber of this motorcycle adopts compound of hydraulic pressure and spring.

It mainly consists of upper tie-in,rubber cover,gasket,rear shock absorber spring,rear shock absorber

lever,piston,damper and lower tie-in.

Rear shock absorber mainly gets the axial pressure of rear wheel.When the rear wheel gets the strike

or shake for the road condition,rear shock absorber will compress and expand.The hydraulic pressure oil of

damper is forced to flow through the damping hole,so it reduces the shake of rear shock absorber spring.

[1]Check the effective stroke and performance of
front shock absorber,and check whether there is
leakage from front shock absorber.

[2]Dismantle four fixed bolt of front shock
absorber

，

and remove the front shock absorber.

Maintain front shock absorber in time if it

has some problems in order to ensure the riding
safety.

CAUTION

Check

front shock

absorber.

Dismantle the

bolt of front shock

absorber.

Содержание ZS250GY-3













































































Результаты поиска

Содержание ZS250GY-3

Отзывы:

Похожие инструкции для ZS250GY-3

Бренды по названию

Популярные бренды

ZONGSHEN ZS250GY-3, Руководство по обслуживанию

Результаты поиска

Содержание ZS250GY-3

Отзывы:

Похожие инструкции для ZS250GY-3

Бренды по названию

Популярные бренды