background image

EN

G

LIS

H

70

2.10   Analysis of brake light

2.11  Analysis of ignition system

Dismantle the cover of brake light and check 

whether its bulb is burned-out.

Brake  light  doesn 

illuminate.

Replace the bulb of 

brake light.

With a lead,make short circuit between 

two connection end of brake light 

switch or two lead end. 

After short circuit,brake light still 

doesn

t illuminate.

After  short  circuit,brake  light 

can illuminate.

The  switch  of  brake  light  is 

adjusted  unproperly  or  the 

inner connecting point has bad 

connection.

Rub the power lead of brake light switch 

with cathode wire with a screwdriver or a 

lead.Check the spark.

When  rubbing  ,there 

is no spark.

T h e  p o w e r  l e a d  b e t w e e n 

ignition switch and brake light 

switch  has  shor t  circuit  or 

open circuit.

When rubbing,there is 

spark.

The  lead  between  brake 

light switch and brake light 

has  short  circuit  or  open 

circuit.

No

Yes

No

Yes

Dismantle high-voltage wire and 

check whether there is spark spurt. 

Engine starts hard.

Fire

No fire

Spark  plug  is 

dagmaged.

Cut off the connecion of charging coil 

of  generator  and  triggering  coil  and 

respectively measure the voltage.

Reconnect it.Turn off the ignition switch and 

observe the high voltage coil.

Measure the DC resistance of 

two coils.

T h e   f l y w h e e l 

rotor  of  generator 

loses  magnetism 

seriously.

Ignition  switch  is 

damaged.

Electronic ignitor is 

damaged.

Replace it.

Ignition  coil  has  open  circuit 

or short circuit.

R e p a i r   o r 

replace it.

Cut  off  the  power  export  end  of 

ignition and measure the voltage. 

Charging and triggering 

coil have short circuit or 

open circuit.

Add  magnetism 

or replace it.

R e p a i r   o r 

replace it.

has voltage

no voltage

Replace it.

Содержание ZS250GY-3













































































Отзывы: