ZONGSHEN ZS250GY-3 Скачать руководство пользователя

Страница: 68 / 76

LIS

2.2 Analysis of battery

Battery cannot be

full charged

Check whether brake light

always illuminates.

A d j u s t o r r e p l a c e

brake switch.

Set ignition switch to OFF position.Remove cathode wire

from storage battery.Connect the cathode end of current

meter to the cathode of storage battery and anode end to

the anode of storage battery.Check the leakage of electric

current.

The value of electric current leakage is

smaller than the stated value.

Check whether the charging coil of

generator has short circuit.

The value of electric current leakage is bigger

than the stated value.(Normally,the electric

current is required to be below 1mA

）

The circuit from rectifier or

commutated adjuster or storage

battery to ignition switch has

short circuit.

R e p l a c e

illuminating coil.

[1]Check whether the electrolyte of storage

battery is enough.

[2]Check whether the electrolyte density of storage battery

is too small.

[3]Check whether plate of storage battery has too much

pbso

or has short circuit.

Yes

Remove the connecting part between the generator lead and vehicle

cable.Measure the resistance with ohmic meter and check whether

the resistance between export lead of charging coil accords with the

standard value.

Resistance value is

smaller than standard

value.

Resistance value accords

with standard value.

Resistance value is

infinite.

Battery cannot be

charged.

Charging coil has

short circuit.

Install the connecting component between generator

lead and vehicle cable.Remove rectifier or the

connecting component between commutated adjuster

and vehicle cable.

C h a r g i n g c o i l o r

other export lead has

open circuit.

Measure the resistance between the export lead of charging coil with

ohmic meter.Check whether the resistance accords with the own

resistance of charging coil.

The circuit from generator to rectifier

or between commutated adjuster has

open circuit or bad connection.

Set multimeter to 0

～

20V DC voltage.Measure the

voltage between the lead ends from the connecting

component to battery(normally it

’

s red wire) and

ground

There is no voltage show.

There is voltage show.

The lead from connecting

component to battery has

open circuit.

M e a s u r e t h e r e c t i f i e r a n d

commutated adjuster with ohmic

meter.Check whether they have

problems.

Yes

Section 2 Analysis of electrical part

2.1 Analysis of battery

Содержание ZS250GY-3













































































Результаты поиска

Содержание ZS250GY-3

Отзывы:

Похожие инструкции для ZS250GY-3

Бренды по названию

Популярные бренды

ZONGSHEN ZS250GY-3, Руководство по обслуживанию

Результаты поиска

Содержание ZS250GY-3

Отзывы:

Похожие инструкции для ZS250GY-3

Бренды по названию

Популярные бренды