Zip HydroTap G4 BC100/75 Скачать руководство пользователя

Страница: 3 / 28

802411 v3.05 09.20 HT BC Compact Instructions

Page 3 of 28

HydroTap Specifications

Installation Checklist ....................................................................................................................4

General Product Features ............................................................................................................5

Important Safety Instructions .......................................................................................................6

Warnings and Regulatory Information ..........................................................................................7

Major Components and Accessories ...........................................................................................8

Technical Specification ................................................................................................................9

Before Installation and Site Requirements ...................................................................................10

Installation Instructions
STEP 1 -

Fit the tap to the benchtop or sink before installing the Command Centre.

(Refer to the Tap installation instruction book 803341)

STEP 2

- Check for adequate ventilation

Section 2- Ventilation

2.1- Ventilation for All Models ............................................................................................11

2.2- Cupboard Air Circulation ............................................................................................12

STEP 3

- Install the Booster Heater (if required)

Section 3 - Booster Heater Installation

3.1- Product Description ....................................................................................................14

3.2- Installation Procedure ................................................................................................15

3.3- To Remove / Install the appliance .............................................................................15

3.4- Braided Hose Connections ........................................................................................16

STEP 4

- Install the Command Centre

Section 4 - Command Centre Installation

4.1- External Bypass Valve ..............................................................................................17

4.2- Hose and tube fitting ..................................................................................................17

4.3- Model BC ..................................................................................................................18

4.4- Model AIO Mains .......................................................................................................19

4.5- Model AIO Vented ......................................................................................................20

4.6- Model 4-In-1 Vented ..................................................................................................21

STEP 5

- Commission the HydroTap

Section 5 - Commissioning

5.1- Select the Language ..................................................................................................22

5.2- Filter Flush .................................................................................................................22

5.3- Boiling Calibration ......................................................................................................23

5.4- Booster .......................................................................................................................23

5.5- Safety Sensor Calibration ..........................................................................................24

5.6- Command-Centre Flush .............................................................................................24

Troubleshooting Table .................................................................................................................25

End of Life Disposal .....................................................................................................................26

Contact Details .............................................................................................................................28

Index

Содержание HydroTap G4 BC100/75





























Результаты поиска

Содержание HydroTap G4 BC100/75

Отзывы:

Похожие инструкции для HydroTap G4 BC100/75

Бренды по названию

Популярные бренды

Zip HydroTap G4 BC100/75, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HydroTap G4 BC100/75

Отзывы:

Похожие инструкции для HydroTap G4 BC100/75

Бренды по названию

Популярные бренды