Zip HydroTap G4 BC100/75 Скачать руководство пользователя

Страница: 25 / 28

802411 v3.05 09.20 HT BC Compact Instructions

Page 25 of 28

Troubleshooting

System Fault

Message

Possible Cause

Solutions

Power board fault

Electrical disruption

Check power supply and all fuses

Interface fault

Internal fault

Call Zip Service

Level board fault

Internal fault

Call Zip Service

Condenser screen blocked Blocked Air filter

Remove blockage / Clean filter / check user guide

Water leak, Isolate mains Water leak

Turn off mains water supply / Call for service

Compressor over-run

Compressor too Hot

Check ventilation

Water supply failed

No water

Check water supply is turned ON

Hot sensor Open

Internal fault

Call Zip Service

Hot sensor Closed

Internal fault

Call Zip Service

Cold sensor Open

Internal fault

Call Zip Service

Cold sensor Closed

Internal fault

Call Zip Service

Flood sensor Open

Internal fault

Call Zip Service

Condenser sensor Closed Internal fault

Check Ventilation / Call Zip Service

Condenser sensor Open

Internal fault

Check ventilation / Call Zip service

Heater fuse / driver fault

Internal fault

Call Zip Service

Heater driver fault

No hot water

Call Zip Service

Compressor driver fault

No chilled water

Call Zip Service

Hot sensor degraded

Internal fault

Call Zip Service

Condenser overtemp.

Blocked air filter

Remove blockage / Clean filter / check user guide

A DC Pump is faulty

Internal fault

Call Zip Service

Steam is too cool

Internal fault

Call Zip Service

Steam sensor Open

Internal fault

Call Zip Service

Steam sensor Closed

Internal fault

Call Zip Service

Over Steamed

Internal fault

Call Zip Service

Hot tank overfilled

Internal fault

Call Zip Service

Comp Fuse/Driver Fault

Internal fault

Call Zip Service

Hot tank under filled

Low water pressure

Check water supply

Boil dry protection

Safety activated

Turn OFF / On power to reset

Flash Mem corrupted

Internal fault

Call Zip Service

Flow Sensor Fault

Internal fault

Call Zip Service

Call an electrician, a plumber, or a Zip Service Provider for assistance, service, spare parts or enquiries.

Содержание HydroTap G4 BC100/75





























Результаты поиска

Содержание HydroTap G4 BC100/75

Отзывы:

Похожие инструкции для HydroTap G4 BC100/75

Бренды по названию

Популярные бренды

Zip HydroTap G4 BC100/75, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HydroTap G4 BC100/75

Отзывы:

Похожие инструкции для HydroTap G4 BC100/75

Бренды по названию

Популярные бренды