Zip HydroTap G4 BC100/75 Скачать руководство пользователя

Страница: 24 / 28

Page 24 of 28

802411 v3.05 09.20 HT BC Compact Instructions

Safety

sensor

Pull both levers forward

Safety Sensor Calibration

(Lever taps)

1. With the unit in Normal operating mode and with the safety enabled

2. Turn the power OFF

3. Pull both tap levers to the forward position

4. Turn ON the power

5. The unit will calibrate the safety switch

6. Return the levers to the neutral position.

7. To check the calibration, dispense Boiling water, in normal light

conditions with the safety enabled.

Light intensity varies from site to site, therefore it is recommended that a re-calibration be performed at the

time of the installation. All direct natural sun light must be shaded from the HydroTap, during the calibration.

This can be achieved by closing any nearby curtains, blinds, or by shielding the HydroTap with a dark cloth.

5.5

Safety Sensor Calibration

5.6

Command-Centre Flush

All G4 HydroTap products are currently sanitised after functional test at the factory. Due to the sanitisation

process, residue from the sanitisation liquid might remain in the product, which requires the products to be

flushed with fresh water at installation.

• Dispense 3 litres of boiling water from the boiling outlet of the HydroTap, equivalent to a complete tankful

of water.

• Dispense 6 litres of chilled water from the chilled outlet of the HydroTap, equivalent to two complete

tankfuls of water.

• Continue with installation.

Содержание HydroTap G4 BC100/75





























Результаты поиска

Содержание HydroTap G4 BC100/75

Отзывы:

Похожие инструкции для HydroTap G4 BC100/75

Бренды по названию

Популярные бренды

Zip HydroTap G4 BC100/75, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HydroTap G4 BC100/75

Отзывы:

Похожие инструкции для HydroTap G4 BC100/75

Бренды по названию

Популярные бренды