Zimmer Biomet Persona Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 72

Zimmer Biomet Persona Скачать руководство пользователя страница 72

Zimmer Biomet does not practice medicine. This technique was
developed in conjunction with health care professionals. This document
is intended for surgeons and is not intended for laypersons. Each surgeon
should exercise his or her own independent judgment in the diagnosis
and treatment of an individual patient, and this information does not
purport to replace the comprehensive training surgeons have received.
As with all surgical procedures, the technique used in each case will
depend on the surgeon’s medical judgment as the best treatment for
each patient. Results will vary based on health, weight, activity and
other variables. Not all patients are candidates for this product and /or
procedure.

All content herein is protected by copyright, trademarks, and other
intellectual property rights, as applicable, owned by or licensed to
Zimmer Biomet or its affiliates unless otherwise indicated, and must not
be redistributed, duplicated or disclosed, in whole or in part, without the
express written consent of Zimmer Biomet.

This material is intended for health care professionals. Distribution to any
other recipient is prohibited.

For indications, contraindications, warnings, precautions, potential
adverse effects and patient counseling information, see the package
insert or contact your local representative; visit www.zimmerbiomet.com
for additional product information.

Caution: Federal (USA) law restricts this device to sale by or on the order
of a surgeon. Rx only.

Check for country product clearance and reference product specific
instructions for use.

Not for distribution in France.

© 2019 Zimmer Biomet

1832.1-GLBL-en-REV0819 MC218585

Authorized Representative

Zimmer GmBH
Sulzerallee 8
8404 Winterthur
Switzerland

Authorized Representative

Zimmer U.K. Ltd.
The Courtyard
9 Lancaster Place
South Marston Park
Swindon, Wiltshire SN3 4FP
United Kingdom

Legal Manufacturer

Zimmer, Inc.
1800 W. Center Street
Warsaw, Indiana 46580
USA

zimmerbiomet.com

CE mark on a surgical technique
is not valid unless there is a CE
mark on the product label.

0086

2797

«
...
70
71
72

Содержание Persona









































































Отзывы:

Нет отзывов