Zimmer Biomet Persona Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 72

Zimmer Biomet Persona Скачать руководство пользователя страница 61

59 |

Persona

®

Revision

Knee System

Surgical Technique

Figure 10

Appendix D: Tibial Central Cone

Implant Assembly

(cont.)

Optional Tibial Augment Assembly

If an augment is being utilized, position the augment
on the underside of the tibial baseplate implant and
align the screws with the thread holes. Use the 3.5
mm hex driver to start both augment screws in a
clockwise direction. Once both screws have been
started, align the augment with the perimeter of the
tibial baseplate implant as desired. Tighten the screws
until the augment is rigidly attached to the tibial
baseplate implant (Figure 10).

Note:

The tibial central cone may need to be lifted

and rotated in order to gain access and tighten the
augments screws.

Note:

Augments must be attached after the stem

has been assembled. The 10 and 15 mm augment
thicknesses will block access to the 2 mm set screw
anteriorly.

A

PPE

N

D

IX

D

Proceed to the Two Stage Cementing Technique
section on page 40.

«
...
59
60
61
62
63
...
»

Содержание Persona









































































Отзывы:

Нет отзывов